Hardwood floors will eventually show wear and tear even when they are made from the highest quality materials. While it might be tempting to get the flooring replaced, there is another alternative. This is through resurfacing the floors. There are some steps involved including the cleaning, sanding, and staining. Each one has to be done with close attention to detail. While it does take time, it's possible to hire atlanta hardwood floor refinishing experts instead. They are able to save you a lot of time and effort.
Over time, even the best hardwood floors show signs of wear and tear. The finishing might start to look worn or scratches may appear. When this happens, you don't always have to replace the pieces because you may be able to resurface them.
There is a lot of work involved with refinishing your own floors. The surfaces need to be thoroughly cleaned. They then need to be sanded. You can use a 180-grit piece of sandpaper or a sanding block for the edges. You may prefer to use an electric sander for the other parts of the room to quicken the process.
The sanding causes a lot of dust. These particles will have to be cleaned up very well before the staining can start. You might need to clean the surfaces numerous times before you can start the staining.
For the staining process, it's advised that you start at the wall that is the furthest away from the entrance. Each patch should be done in small increments and the next patch started before the edge dries. The edges of the stain should overlap. This will prevent unwanted lines from forming.
When the staining has been applied to the small portion of the edges, you may use a roller for applying the substance further out towards the center of the floor. Again, it should only be done in small batches. The stain patches should be overlapping to prevent lines from forming. This process may be used for each coating needed.
Resurfacing a floor requires time and effort. It is possible to do the work yourself. However, if you hire the experts in the area, they supply all of the equipment needed while saving you effort and time.
Resurfacing a floor can be a great way to make the surface look as good as new. It can be a great alternative to installing new flooring when the older one is showing wear and tear. There are numerous steps involved in the stages of cleaning, sanding, staining, and finishing the hardwood. Rather than completing the job yourself, it is often better to call in the experts.
Over time, even the best hardwood floors show signs of wear and tear. The finishing might start to look worn or scratches may appear. When this happens, you don't always have to replace the pieces because you may be able to resurface them.
There is a lot of work involved with refinishing your own floors. The surfaces need to be thoroughly cleaned. They then need to be sanded. You can use a 180-grit piece of sandpaper or a sanding block for the edges. You may prefer to use an electric sander for the other parts of the room to quicken the process.
The sanding causes a lot of dust. These particles will have to be cleaned up very well before the staining can start. You might need to clean the surfaces numerous times before you can start the staining.
For the staining process, it's advised that you start at the wall that is the furthest away from the entrance. Each patch should be done in small increments and the next patch started before the edge dries. The edges of the stain should overlap. This will prevent unwanted lines from forming.
When the staining has been applied to the small portion of the edges, you may use a roller for applying the substance further out towards the center of the floor. Again, it should only be done in small batches. The stain patches should be overlapping to prevent lines from forming. This process may be used for each coating needed.
Resurfacing a floor requires time and effort. It is possible to do the work yourself. However, if you hire the experts in the area, they supply all of the equipment needed while saving you effort and time.
Resurfacing a floor can be a great way to make the surface look as good as new. It can be a great alternative to installing new flooring when the older one is showing wear and tear. There are numerous steps involved in the stages of cleaning, sanding, staining, and finishing the hardwood. Rather than completing the job yourself, it is often better to call in the experts.
About the Author:
Ainsley G. Zaveri is a flooring specialist who helps individual homeowners make the best choices in getting their home flooring done beautifully and economically. If you are interested in learning more about hardwood floor refinishing she suggests you visit her friend's at .
Hardwood floors will eventually show wear and tear even when they are made from the highest quality materials. While it might be tempting to get the flooring replaced, there is another alternative. This is through resurfacing the floors. There are some steps involved including the cleaning, sanding, and staining. Each one has to be done with close attention to detail. While it does take time, it's possible to hire atlanta hardwood floor refinishing experts instead. They are able to save you a lot of time and effort.
Over time, even the best hardwood floors show signs of wear and tear. The finishing might start to look worn or scratches may appear. When this happens, you don't always have to replace the pieces because you may be able to resurface them.
There is a lot of work involved with refinishing your own floors. The surfaces need to be thoroughly cleaned. They then need to be sanded. You can use a 180-grit piece of sandpaper or a sanding block for the edges. You may prefer to use an electric sander for the other parts of the room to quicken the process.
The sanding causes a lot of dust. These particles will have to be cleaned up very well before the staining can start. You might need to clean the surfaces numerous times before you can start the staining.
For the staining process, it's advised that you start at the wall that is the furthest away from the entrance. Each patch should be done in small increments and the next patch started before the edge dries. The edges of the stain should overlap. This will prevent unwanted lines from forming.
When the staining has been applied to the small portion of the edges, you may use a roller for applying the substance further out towards the center of the floor. Again, it should only be done in small batches. The stain patches should be overlapping to prevent lines from forming. This process may be used for each coating needed.
Resurfacing a floor requires time and effort. It is possible to do the work yourself. However, if you hire the experts in the area, they supply all of the equipment needed while saving you effort and time.
Resurfacing a floor can be a great way to make the surface look as good as new. It can be a great alternative to installing new flooring when the older one is showing wear and tear. There are numerous steps involved in the stages of cleaning, sanding, staining, and finishing the hardwood. Rather than completing the job yourself, it is often better to call in the experts.
Over time, even the best hardwood floors show signs of wear and tear. The finishing might start to look worn or scratches may appear. When this happens, you don't always have to replace the pieces because you may be able to resurface them.
There is a lot of work involved with refinishing your own floors. The surfaces need to be thoroughly cleaned. They then need to be sanded. You can use a 180-grit piece of sandpaper or a sanding block for the edges. You may prefer to use an electric sander for the other parts of the room to quicken the process.
The sanding causes a lot of dust. These particles will have to be cleaned up very well before the staining can start. You might need to clean the surfaces numerous times before you can start the staining.
For the staining process, it's advised that you start at the wall that is the furthest away from the entrance. Each patch should be done in small increments and the next patch started before the edge dries. The edges of the stain should overlap. This will prevent unwanted lines from forming.
When the staining has been applied to the small portion of the edges, you may use a roller for applying the substance further out towards the center of the floor. Again, it should only be done in small batches. The stain patches should be overlapping to prevent lines from forming. This process may be used for each coating needed.
Resurfacing a floor requires time and effort. It is possible to do the work yourself. However, if you hire the experts in the area, they supply all of the equipment needed while saving you effort and time.
Resurfacing a floor can be a great way to make the surface look as good as new. It can be a great alternative to installing new flooring when the older one is showing wear and tear. There are numerous steps involved in the stages of cleaning, sanding, staining, and finishing the hardwood. Rather than completing the job yourself, it is often better to call in the experts.
About the Author:
Ainsley G. Zaveri is a flooring specialist who helps individual homeowners make the best choices in getting their home flooring done beautifully and economically. If you are interested in learning more about hardwood floor refinishing she suggests you visit her friend's at .
No comments:
Post a Comment