A furnace is a very important piece of equipment in any home. As such, it is important to ensure that it is working well at all times. Part of achieving this goal involves regularly cleaning and maintaining various parts of the equipment in good condition. When the equipment is not cleaned well, it starts to use more gas, oil, or electricity, leading to higher maintenance costs. It also becomes increasingly inefficient. When in need of oil furnace cleaning PA should be visited.
For several parts of the equipment to work efficiently, they have to be cleaned properly. The cleanliness of the entire equipment must be maintained, but more focus needs to be given to three main components. The three components are the filter system, the blower, and the heat exchanger. The equipment becomes less efficient if it is not cleaned for long, leading to accumulation of dirt.
The lifespan of the equipment is usually dependent on how clean these components are kept. For one to be able to clean the three components properly, one needs some prior knowledge so as to avoid damaging them during cleaning. To clean the filter and blower fan, one should begin by finding the access panel. This component is usually located on the outside of the furnace.
Most models have access panels located in the space between the blower and return-air duct. The duct is located on the upper side, then the access panel follows, while the blower comes last below it. As for the filter, it is located on the front side of the equipment. One ought to remove the front panel to access it. There may be a separate door on the filter. Prior to engaging in any of these activities, power supply should be switched off.
For the filter to be cleaned, it has to be removed from the compartment where it sits. Removing the filter from the compartment should be easy. In case there is difficulty in getting the filter out, one should be keen with how they proceed. One should inspect the filter for any dirt and if loose debris is present, it should be cleaned off.
Once all the loose dirt particles have been removed, tap water mixed with mild soap should be used to clean the remaining dirt. After all dirt has been removed, the filter should be rinsed using clean water and allowed to dry adequately. If there is any visible damage to the filter, it should be replaced if it is a disposable model.
After cleaning the filter, the blower assembly should then be cleaned. The entire front panel has to be removed before cleaning this components. Sometimes panels are held in position by screws. The screws have to be unscrewed for the panel to be removed. Hinges should be opened for panels that are held in position by hinges. The fan should then be removed from its compartment and cleaned.
The fan is help on tracks and may be connected by a wire to the rest of the equipment. The fan and the blower assembly should also be cleaned using water and mild soap. Fan blades and spaces between them can be cleaned better using a toothbrush. The same process should be used to clean the heat exchanger.
For several parts of the equipment to work efficiently, they have to be cleaned properly. The cleanliness of the entire equipment must be maintained, but more focus needs to be given to three main components. The three components are the filter system, the blower, and the heat exchanger. The equipment becomes less efficient if it is not cleaned for long, leading to accumulation of dirt.
The lifespan of the equipment is usually dependent on how clean these components are kept. For one to be able to clean the three components properly, one needs some prior knowledge so as to avoid damaging them during cleaning. To clean the filter and blower fan, one should begin by finding the access panel. This component is usually located on the outside of the furnace.
Most models have access panels located in the space between the blower and return-air duct. The duct is located on the upper side, then the access panel follows, while the blower comes last below it. As for the filter, it is located on the front side of the equipment. One ought to remove the front panel to access it. There may be a separate door on the filter. Prior to engaging in any of these activities, power supply should be switched off.
For the filter to be cleaned, it has to be removed from the compartment where it sits. Removing the filter from the compartment should be easy. In case there is difficulty in getting the filter out, one should be keen with how they proceed. One should inspect the filter for any dirt and if loose debris is present, it should be cleaned off.
Once all the loose dirt particles have been removed, tap water mixed with mild soap should be used to clean the remaining dirt. After all dirt has been removed, the filter should be rinsed using clean water and allowed to dry adequately. If there is any visible damage to the filter, it should be replaced if it is a disposable model.
After cleaning the filter, the blower assembly should then be cleaned. The entire front panel has to be removed before cleaning this components. Sometimes panels are held in position by screws. The screws have to be unscrewed for the panel to be removed. Hinges should be opened for panels that are held in position by hinges. The fan should then be removed from its compartment and cleaned.
The fan is help on tracks and may be connected by a wire to the rest of the equipment. The fan and the blower assembly should also be cleaned using water and mild soap. Fan blades and spaces between them can be cleaned better using a toothbrush. The same process should be used to clean the heat exchanger.
About the Author:
If you are searching for an oil furnace cleaning PA service, you can trust this source. Get all the specifics by clicking on this link http://www.capitolcityoil.com/Furnace-Cleanings.html.
A furnace is a very important piece of equipment in any home. As such, it is important to ensure that it is working well at all times. Part of achieving this goal involves regularly cleaning and maintaining various parts of the equipment in good condition. When the equipment is not cleaned well, it starts to use more gas, oil, or electricity, leading to higher maintenance costs. It also becomes increasingly inefficient. When in need of oil furnace cleaning PA should be visited.
For several parts of the equipment to work efficiently, they have to be cleaned properly. The cleanliness of the entire equipment must be maintained, but more focus needs to be given to three main components. The three components are the filter system, the blower, and the heat exchanger. The equipment becomes less efficient if it is not cleaned for long, leading to accumulation of dirt.
The lifespan of the equipment is usually dependent on how clean these components are kept. For one to be able to clean the three components properly, one needs some prior knowledge so as to avoid damaging them during cleaning. To clean the filter and blower fan, one should begin by finding the access panel. This component is usually located on the outside of the furnace.
Most models have access panels located in the space between the blower and return-air duct. The duct is located on the upper side, then the access panel follows, while the blower comes last below it. As for the filter, it is located on the front side of the equipment. One ought to remove the front panel to access it. There may be a separate door on the filter. Prior to engaging in any of these activities, power supply should be switched off.
For the filter to be cleaned, it has to be removed from the compartment where it sits. Removing the filter from the compartment should be easy. In case there is difficulty in getting the filter out, one should be keen with how they proceed. One should inspect the filter for any dirt and if loose debris is present, it should be cleaned off.
Once all the loose dirt particles have been removed, tap water mixed with mild soap should be used to clean the remaining dirt. After all dirt has been removed, the filter should be rinsed using clean water and allowed to dry adequately. If there is any visible damage to the filter, it should be replaced if it is a disposable model.
After cleaning the filter, the blower assembly should then be cleaned. The entire front panel has to be removed before cleaning this components. Sometimes panels are held in position by screws. The screws have to be unscrewed for the panel to be removed. Hinges should be opened for panels that are held in position by hinges. The fan should then be removed from its compartment and cleaned.
The fan is help on tracks and may be connected by a wire to the rest of the equipment. The fan and the blower assembly should also be cleaned using water and mild soap. Fan blades and spaces between them can be cleaned better using a toothbrush. The same process should be used to clean the heat exchanger.
For several parts of the equipment to work efficiently, they have to be cleaned properly. The cleanliness of the entire equipment must be maintained, but more focus needs to be given to three main components. The three components are the filter system, the blower, and the heat exchanger. The equipment becomes less efficient if it is not cleaned for long, leading to accumulation of dirt.
The lifespan of the equipment is usually dependent on how clean these components are kept. For one to be able to clean the three components properly, one needs some prior knowledge so as to avoid damaging them during cleaning. To clean the filter and blower fan, one should begin by finding the access panel. This component is usually located on the outside of the furnace.
Most models have access panels located in the space between the blower and return-air duct. The duct is located on the upper side, then the access panel follows, while the blower comes last below it. As for the filter, it is located on the front side of the equipment. One ought to remove the front panel to access it. There may be a separate door on the filter. Prior to engaging in any of these activities, power supply should be switched off.
For the filter to be cleaned, it has to be removed from the compartment where it sits. Removing the filter from the compartment should be easy. In case there is difficulty in getting the filter out, one should be keen with how they proceed. One should inspect the filter for any dirt and if loose debris is present, it should be cleaned off.
Once all the loose dirt particles have been removed, tap water mixed with mild soap should be used to clean the remaining dirt. After all dirt has been removed, the filter should be rinsed using clean water and allowed to dry adequately. If there is any visible damage to the filter, it should be replaced if it is a disposable model.
After cleaning the filter, the blower assembly should then be cleaned. The entire front panel has to be removed before cleaning this components. Sometimes panels are held in position by screws. The screws have to be unscrewed for the panel to be removed. Hinges should be opened for panels that are held in position by hinges. The fan should then be removed from its compartment and cleaned.
The fan is help on tracks and may be connected by a wire to the rest of the equipment. The fan and the blower assembly should also be cleaned using water and mild soap. Fan blades and spaces between them can be cleaned better using a toothbrush. The same process should be used to clean the heat exchanger.
About the Author:
If you are searching for an oil furnace cleaning PA service, you can trust this source. Get all the specifics by clicking on this link http://www.capitolcityoil.com/Furnace-Cleanings.html.
No comments:
Post a Comment